Choice of category
Solder kits
Infrared
IrDA
LCD
G-LCD
Special offers
Fan articles
About
Help
  
Articles in this category
You are here: Fanshop -> Solder kits -> Infrared

Description Order No. Price Qty Buy Delete
USB Ultra IR-Receiver v2.0
Also Power On/Off the PC (USB-Version)		 2036 24.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The newest USB version with two Atmel ICs, two LEDs and
more sensitive ir receiver !
With the new USB Ultra infrared receiver v2.0 of the Modding section
it's possible to power ON / OFF the PC with commercial universal
infrared remote control units.
Of course it's not only supported to switch on the PC, in addition it's also
possible to remote control PC programs e.g. Winamp, OS, the Mouse, etc.
by using software like Girder.
Guides and links to Windows and Linux infrared receiver software downloads
are available in the Redaktion ocinside.de modding area.
The red control LED shows received infrared signals and the
green LED light up when a programmed power on/off signal is received.

Following electronic components are contained in the set:
1x TSOP 31238 IR receiver module 38kHz
1x Atmel ATtiny45-20PU - already programmed!
1x Atmel ATtiny13V-10PU - already programmed!
2x 8-pole IC-Socket
1x Optoelectronic coupler CNY17-2
1x 12MHz crystal
2x zener diodes 3.6V
1x red low current LED
1x green low current LED
1x 4.7µF capacitor
1x 100nF capacitor
2x 22pF capacitor
3x 1,5 K resistor
2x 68 ohms resistor
1x 390 ohms resistor
1x 2-pole pin row
1x Jumper with flag for simple remove and put on
1x USB A-plug with approx. 1 meter long cable
1x 2 pole approx. 1 meter long cable
1x approx. 68x32mm breadboard
Here's a solder guide for the kit ...
Description Order No. Price Qty Buy Delete
IR-Box
Nice case for the IR-Receiver e.g. USB Ultra IR v2.0		 2037 3.50 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The infrared receiver kits had to go without a chassis so far and it's time to change this.
Now there's the new IR box available, where one can insert for example the PCB of the brand-new USB Ultra infrared receiver v2.0, in order to protect the electronic devices and to get a more beautiful construction for the PC or HTPC.
Of course it is also possible to integrate different IR receivers into the small black plastic box, because the IR box comes without cut-out and can be thus adjusted according to desire.

Following components are contained in the scope of delivery:
1x black plastic chassis in two half shells
4x screws
External dimensions: approx. 50 x 28 x 72 mm (W/H/D)

Here's an IR Box assembly and modification guide ...
Description Order No. Price Qty Buy Delete
IR-Repeater USB Edition
Remote control receiver through a wall or in a HiFi cupboard		 2056 16.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The new IR-Repeater USB Edition offers an easy way to hide HiFi devices and the TV-receiver in a HiFi cupboard or even remote control a PC, Mediaplayer, etc. with a remote control unit from another room.
Infrared signals of a remote controls do not pass a wall or into a cupboard, therefore this IR extender receives the infrared signals, modulate the signals and lead them over a cable to two IR transmitting diodes, which send the signal to the respective HiFi equipment, HTPC, Mediaplayer or PC with IR receiver.
The power supply for the IR Repeater USB Edition is obtained directly via a free USB port and therefore will not require any battery as with the first version of the IR Repeater.

Following electronic components are contained in the set:
1x Vishay TSOP31238 38 kHz IR receiver module
2x LD274 infrared transmitting diode
1x 8-pole IC-Socket
1x NE555 IC
2x BC 549C transistor
1x 4.7µF capacitor
1x 1nF capacitor
1x 47 Ohm resistor
2x 1.5 K resistor
1x 6.8 K resistor
1x 10 K resistor
1x approx. 48x33mm breadboard
1x 2 pole approx. 1 meters long cable
1x approx. 1 meter cable with USB Type-A plug

Here's a solder guide for the IR-Repeater USB Edition kit ...
Description Order No. Price Qty Buy Delete
IR-Repeater
Remote control receiver through a wall or in a HiFi cupboard		 2053 16.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The new IR-Repeater offers an easy way to hide HiFi devices and the TV-receiver in a HiFi cupboard or even remote control a PC, Mediaplayer, etc. with a remote control unit from another room.
Infrared signals of a remote controls do not pass a wall or into a cupboard, therefore this IR extender receives the infrared signals, modulate the signals and lead them over a cable to two IR transmitting diodes, which send the signal to the respective HiFi equipment, HTPC, Mediaplayer or PC with IR receiver.

Following electronic components are contained in the set:
1x Vishay TSOP31238 38 kHz IR receiver module
2x LD274 infrared transmitting diode
1x 8-pole IC-Socket
1x NE555 IC
1x 7805 voltage regulator
1x BD 139 transistor
1x BC 549C transistor
1x red low current LED
1x 4.7µF capacitor
1x 1nF capacitor
1x 47 Ohm resistor
3x 1.5 K resistor
1x 6.8 K resistor
1x 10 K resistor
1x approx. 54x32mm breadboard
1x 2 pole approx. 1 meter long cable
1x 9V battery clip

A 9 Volt battery is not included in the kit.

Here's a solder guide for the IR-Repeater kit ...
Description Order No. Price Qty Buy Delete
IR-Repeater Box
Nice case for the IR-Repeater with battery box		 2054 3.90 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
This is the IR-Repeater box, where one can insert for example the PCB of the brand-new IR-Extender kit, in order to protect the electronic components and to get a more beautiful construction.
Of course it is also possible to integrate different devices into the small black plastic box, because the IR-Repeater box comes without cut-out and can be thus adjusted according to desire.

Following components are contained in the scope of delivery:
1x black plastic chassis in two half shells with battery case
1x battery case cover
1x screw
External dimensions: approx. 62 x 26 x 103 mm (W/H/D)

Here's an IR-Repeater Box assembly and modification guide ...
Description Order No. Price Qty Buy Delete
USB Slotbracket
Slot bracket with 2x USB-A to 5-pole connector		 2049 3.50 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The USB Slotbracket is a USB slot bracket with two USB-A connectors over approx. a 20cm lead on two 5-pin headers.
Thus one can connect the USB Ultra IR kit or USB IR kit externally to a free internal USB pinheader of the motherboard.

Compare the pin allocation of the 5-pin headers with the pin allocation from the motherboard manual before connecting and take care to connect it right:
1 VCC (red)
2 DATA- (white)
3 DATA+ (green)
4 GND (black)
5 GND (black)
Description Order No. Price Qty Buy Delete
Internal USB Connector Cable
USB cable internal with 2x USB-A to 5-pin header		 2050 2.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The Internal USB Connector Cable is requested by some visitors and is an USB cable with one USB-A connector over approx. a 20cm lead to one 5-pin header.
Thus one can connect the USB Ultra IR kit or USB IR kit internally to a free internal USB pinheader of the motherboard.

Compare the pin allocation of the 5-pin headers with the pin allocation from the motherboard manual before connecting and take care to connect it right:
1 VCC (red)
2 DATA- (white)
3 DATA+ (green)
4 GND (black)
5 GND (black)
Description Order No. Price Qty Buy Delete
USB IR-Receiver v1.1
Infrared Remote Control over USB (USB-Version)		 2027 15.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The USB infrared receiver v1.1 from the Modding section as complete solder kit!

Following electronic components are contained in the set:
1x TSOP 31238 or TSOP 1738 IR receiver module 38kHz
1x Atmel ATtiny45-20PU (instead of AT90S2323-10) - already programmed!
Important: do not program the older AT90S2323-10 Firmware to this IC
1x 8-pole IC-Socket
1x 12MHz crystal
1x 4.7µF capacitor
1x 10µF capacitor
1x 100nF capacitor
1x 1.5 K resistor
1x USB A-plug with approx. 1 meter long cable
1x approx. 3 cm heat shrink tube
1x approx. 35x22mm breadboard
Here's a solder guide for the kit ...

Note about the USB IR v1.1 kit:
Depending on the motherboard it can be necessary to use the USB IR 1.1 with the included 100 ohm resistors or to attach it with USB hub to the PC.
To prevent this, the new USB Ultra IR v2.0 is extended with Zener diodes.
Description Order No. Price Qty Buy Delete
Ultra IR-Receiver v1.1
Also Power On/Off the PC (serial Version)		 2031 15.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
With the new Ultra infrared receiver of the Modding section
it's possible to power ON / OFF the PC with commercial infrared
remote control units.
Of course in addition it's possible to remote control PC programs
e.g. Winamp, OS, the Mouse, etc. by using software like WinLIRC or Girder.

Following electronic components are contained in the set:
1x TSOP 31238 or TSOP 1738 IR receiver module 38kHz
1x Atmel ATtiny13V-10PU (instead of AT90S2343-10) - already programmed!
1x 8-pole IC-Socket
1x Optoelectronic coupler CNY17-2
1x 4.7µF capacitor
1x 100nF capacitor
1x 4.7 K resistor
1x 390 ohms resistor
1x 9 pole SUB-D socket
1x 2-pole pin row
1x Jumper with flag for simple remove and put on
1x USB A-plug with approx. 1 meter long cable
1x minimum 3 pole approx. 1 meter long shielded data cable
1x approx. 3 cm heat shrink tube
1x approx. 35x30mm breadboard
Here's a solder guide for the kit ...
Description Order No. Price Qty Buy Delete
Luxus IR-Receiver
Distance approx. 15-20 meters (serial Version)		 2001 5.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
The Luxus infrared receiver of the Modding section as complete solder kit !

Following electronic components are contained in the set:
1x TSOP 31238 or TSOP 1738 IR receiver module 38kHz
1x 4.7µF capacitor
1x 1N4148 diode
1x 4.7 K resistor
1x µA 78L05 voltage regulator
1x 9 pole SUB-D socket with housing
1x minimum 3 pole shielded data cable (approx. 1 m)
1x approx. 13x17 mm breadboard
1x approx. 3 cm heat shrink tube
Here's a solder guide for the kit ...
Description Order No. Price Qty Buy Delete
Atmel ATTINY45-20PU
Already programmed with USB firmware		 2032 6.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
Due to some inquiries the Atmel Tiny 45 20PU IC is now available
individually in the Fanshop.
The firmware is already programmed and tested.

Following electronic components are contained:
1x Atmel ATtiny45-20PU - already programmed !
1x 8-pole IC-Socket

Other components are necessary to build an USB IR-Receiver !
Description Order No. Price Qty Buy Delete
Atmel ATTINY13V-10PU
Already programmed with Power On/Off firmware		 2033 6.00 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
Due to some inquiries the Atmel Tiny 13V 10PU IC is now available
individually in the Fanshop.
The firmware is already programmed and tested.

It's also very useful to upgrade existing infrared receiver kits with
more switch functions (e.g. RESET).

Following electronic components are contained:
1x Atmel ATtiny13V-10PU - already programmed !
1x 8-pole IC-Socket´
1x Optoelectronic coupler CNY17-2

Other components are necessary to build an IR-Receiver with Power on/off function !
Description Order No. Price Qty Buy Delete
TSOP31238
Addtional TSOP to expand IR		 2055 2.50 €

plus shipping
 - - -
At present unfortunately this article is not deliverable!
With this additional TSOP 31238 receiver our IR repeater and IR receiver kits can be extended easily.
Just connect the TSOP parallel to the others, for example, in different rooms to operate the IR-Repeater or IR-Receiver from this room.
×


Copyright 1999 - 2024 by www.ocinside.de